A hoodie is specified in seven parts: the body fabric and its weight, the hood, the pocket, the rib, the trims, the wash and the decoration. Most retail hoodies sit between about 280 and 400 GSM in French terry or brushed fleece, and almost every quoting dispute traces back to one of those seven being left open.
Two quotes for "a 320 GSM cotton hoodie" can differ widely and both be fair, because one assumes a two-panel single-layer hood and plain cotton rib, and the other a three-panel lined hood, metal eyelets, cotton-elastane rib and a garment dye. The guide below works through each part in the order a sample room would ask about them.
India's knit clusters, Tirupur above all, have deep capacity in fleece and terry garments; the Tirupur knitwear guide covers how that cluster is organised. Everything that follows applies wherever the order is placed.
French terry or fleece: which body fabric does a hoodie need?
Both start as the same looped knit. French terry leaves the loops on the inner face unbrushed, so it is lighter, cooler and holds a cleaner shape. Fleece has the loops brushed into a soft nap, which traps warmth and adds bulk at the same weight. Terry suits spring ranges, layering pieces and garment-dyed styles; fleece suits winter weights and the classic heavy pullover.
The fibre is the second decision. Most hoodies are 100% cotton or a cotton-rich blend with polyester, commonly somewhere from 80/20 to 60/40. Cotton gives a dry hand and takes garment dye and discharge print well. Polyester in the blend reduces shrinkage and speeds drying, at the cost of pilling that stays on the surface and a less natural hand. Organic and recycled versions of both exist and add their own documentation to the programme.
What GSM should a hoodie be?
Typically 280 to 350 GSM for a midweight hoodie and 350 to 450 GSM for a heavyweight one. Below about 280 GSM a hoodie reads as lightweight or summer weight; above 450 GSM it moves into the heavy, structured streetwear end.
| Weight class | Typical fabric GSM | Common body | How it wears |
|---|---|---|---|
| Lightweight | 220 to 280 | French terry | Drapes, layers under a jacket, suits warmer months |
| Midweight | 280 to 350 | French terry or fleece | The core retail weight, year-round |
| Heavyweight | 350 to 450 | Fleece or heavy terry | Holds its shape, boxy silhouette, winter |
| Extra heavyweight | 450 and above | Heavy fleece or dense terry | Structured streetwear, high fabric cost |
State the GSM on the finished, washed fabric, with a tolerance. A greige fabric gains weight as it shrinks in dyeing and finishing, and a garment-dyed hoodie gains more in the garment wash, so "320 GSM" on the roll and "320 GSM" on the finished garment are different specifications. The fabric GSM guide covers how to write the tolerance.
Weight also changes the pattern. A heavyweight fabric needs more ease at the armhole and a larger hood opening to sit right, and its seams carry more bulk, so a block developed in 280 GSM terry does not transfer cleanly to 420 GSM fleece.
How should the hood and pocket be constructed?
Specify the hood's panel count, its lining and its opening measurement, and the pocket's type, depth and reinforcement. These are the details that separate a basic hoodie from a premium one, and they are where a sample most often differs from the reference garment.
| Element | Common options | What to specify |
|---|---|---|
| Hood panels | Two-panel with a centre seam; three-panel with a centre strip | Panel count, and whether the centre strip is self fabric or contrast |
| Hood lining | Single layer; double layer in self fabric; lined in jersey | Lining fabric and colour, and whether it shows at the opening |
| Hood opening | Measured edge to edge along the face opening | Measurement with tolerance on every size |
| Back neck | Neck tape over the seam, or a coverstitched finish | Tape width and fabric |
| Kangaroo pocket | Patch pouch with turned and topstitched edges | Pocket width, depth, opening angle and height above the hem rib |
| Split pockets | Two pouches either side of a zip; side-seam pockets | Placement and pocket bag fabric |
| Reinforcement | Bartacks at pocket ends, stay tape at the zip | Positions and stitch type |
A three-panel hood sits closer to the head and holds its shape when down; a two-panel hood is cheaper and peaks at the top. A double-layer hood adds weight and cost and stops the inside face showing, which matters on fleece because the brushed back is a different colour value from the face.
Zip-through hoodies add a zip decision. Moulded plastic and metal zips each need the length set after the body fabric has been shrinkage-tested, because a body that shrinks around a zip that does not leaves a wavy front placket that cannot be pressed out.
What rib, drawcord and eyelet details need specifying?
The rib's structure and fibre, the cord's shape and tipping, and the eyelet type with its reinforcement. They are small parts with outsized effects on how the garment looks after a month of wear.
Cuff and hem rib is usually 1x1 or 2x2 rib, knitted in cotton with a small share of elastane, commonly around 3 to 5%, so the cuff recovers after being pushed up the arm. Without elastane a cotton rib grows and stays stretched. The rib is often knitted and dyed separately from the body, so its shade has to be approved against the body fabric, not only against the colour standard, or the cuffs read lighter or darker than the sleeve. State rib length at cuff and hem as finished measurements.
| Trim | Options | Specification point |
|---|---|---|
| Cuff and hem rib | 1x1 or 2x2, cotton or cotton-elastane | Structure, elastane share, finished length, shade against body |
| Drawcord | Flat or round, cotton or polyester | Width, length outside the eyelets, colour |
| Cord ends | Metal or plastic aglets, silicone tips, knots | Tip type and pull strength |
| Eyelets | Metal eyelets with a backing washer; embroidered eyelets | Finish, metal composition, reinforcement behind the hole |
| Cord anchor | Stitched at centre back | So the cord cannot be pulled out |
Metal eyelets need a reinforcing layer behind them, usually a small fused patch, or the hole tears under the pull of the cord. Embroidered eyelets avoid metal altogether and suit garment-dyed styles, where metal can mark the fabric in the wash.
Children's hoodies need a separate decision. In the United States, the Consumer Product Safety Commission has determined that hood and neck drawstrings on children's upper outerwear in sizes 2T to 12 present a strangulation hazard and are a substantial product hazard. The kidswear safety guide covers how childrenswear programmes handle cords and trims. [1]
How do you stop a hoodie shrinking, twisting or pilling?
By controlling the fabric before it is cut. Pre-shrinking, compacting and the right knitting construction prevent most post-wash complaints, and a wash test on a finished sample confirms it before bulk.
| Problem | Usual cause | Control |
|---|---|---|
| Shrinks in length after washing | Fabric not compacted or pre-shrunk | Compacted finish, shrinkage limit on the tech pack |
| Side seams twist toward the front | Spirality in tubular knit | Open-width finishing, yarn twist balance, tested spirality limit |
| Pilling on the face or inside | Brushing loosens fibres; polyester anchors pills | Anti-pill finish, yarn choice, pilling grade |
| Cuffs and hem stay stretched | Rib without elastane, or weak elastane | Cotton-elastane rib, recovery check |
| Zip placket waves | Body shrinks more than the zip tape | Shrinkage-tested fabric before zip length is set |
| Garment-dyed piece comes out small | Garment wash shrinkage not built into the pattern | Pattern graded up for the measured shrinkage |
Shrinkage limits are commonly written as a maximum percentage in length and width after a stated wash procedure, and a midweight cotton terry is often specified at around 5% or less.
Garment dyeing changes the arithmetic. The hoodie is sewn in undyed fabric and then dyed and washed as a finished piece, so it shrinks after it is made. The pattern is cut larger by the measured shrinkage, and that figure is only known after a test batch through the actual dye process. Expect some seam puckering and slight colour variation between pieces; the sealed sample sets how much is acceptable.
Which decoration methods suit a hoodie?
Screen printing and embroidery cover most hoodie decoration, with puff printing and appliqué for raised effects. The choice depends on the artwork, the fabric weight and the wash.
| Method | Works best for | Watch on a hoodie |
|---|---|---|
| Plastisol screen print | Bold, opaque artwork on any colour | Heavy hand on large prints; cracking if cured wrongly |
| Water-based and discharge print | Soft hand on cotton, vintage look | Needs high cotton content; colour range on dark grounds |
| Puff print | Raised graphics and logos | Fine detail fills in; height varies with cure |
| Flat embroidery | Logos, small chest marks | Puckering on fleece without the right backing |
| 3D puff embroidery | Raised lettering | Needs stable, heavier fabric |
| Chenille appliqué | Varsity patches, large raised marks | Weight and cost; edges must be secured for washing |
| Digital or transfer print | Photographic or many-colour artwork | Hand and wash durability vary by system |
Embroidery on fleece needs the right stabiliser behind it, because the knit stretches under the needle and puckers once the hoop comes off. The embroidery and appliqué guide covers digitising, backing and pricing.
Decide whether decoration goes on cut panels or the finished garment. Printing a flat front panel before sewing is easier to register and cheaper, but it commits the panel before the garment is assembled. Garment-dyed styles are usually decorated after dyeing, since many prints change colour in the dye bath.
What drives the cost of a hoodie?
Fabric weight, above everything else. A hoodie uses a lot of fabric per piece, and fabric is bought by the kilo, so each step up in GSM raises the cost of every garment. After fabric come finishing, construction details, decoration and packing.
| Cost driver | Why it moves the price |
|---|---|
| Fabric GSM and consumption | More grams per square metre, more kilos per piece |
| Fibre | Organic cotton and certified recycled fibres cost more and add documentation |
| Finishing | Brushing, enzyme washing, garment dyeing and washes add process cost and loss |
| Construction | Three-panel or lined hood, zip, split pockets and extra panels add sewing time |
| Trims | Rib quality, metal eyelets, custom aglets, branded zip pullers |
| Decoration | Colours, print size, stitch count, number of placements |
| Packing and freight | Hoodies are bulky; fewer pieces per carton raise freight per piece |
Sampling usually runs in stages: a development or proto sample to settle the fabric and look, a fit sample on the base size, a size set across the range and a pre-production sample in bulk fabric with bulk trims. For a hoodie, add a decoration strike-off and a washed sample that proves shrinkage and twist. The sampling process guide explains each round.
Packing deserves a line on the spec. A heavyweight hoodie folded with tissue and a size sticker in an individual polybag takes up far more carton space than a T-shirt, so fold dimensions, polybag size and pieces per carton change landed cost. The carton and container calculator works through the cubic volume.
Short FAQ
What is a good GSM for a hoodie?
Typically 280 to 350 GSM for an everyday midweight hoodie. Heavyweight styles run 350 to 450 GSM, and lightweight terry hoodies sit around 220 to 280 GSM.
Is 400 GSM a heavy hoodie?
Yes. At 400 GSM a hoodie sits firmly in the heavyweight band, with a structured hang and noticeably more warmth than a midweight piece.
Does a cotton-polyester blend shrink less than 100% cotton?
Yes, generally. The polyester share reduces shrinkage and speeds drying, though it raises the risk of visible pilling over time.
Should cuffs and hem rib contain elastane?
Yes, in most programmes. A small elastane share lets the rib recover after stretching, where a pure cotton rib tends to stay stretched out.
Can a hoodie be garment dyed after decoration?
Sometimes, but not with every method. Many prints change colour or texture in the dye bath, so decoration is usually applied after dyeing unless a dye-safe method has been tested.
Write the seven parts down before the first quote
A hoodie quote is only comparable once the body fabric and finished GSM, the hood, the pocket, the rib, the trims, the wash and the decoration are fixed on paper. Settle those, test shrinkage and twist on a washed sample, and approve rib shade against the body, and most of the problems that surface in bulk never arrive. Surajmal Shobhachand supplies hoodies and sweatshirts in loopback terry and brushed fleece.
Ready to source with confidence?
Send a brief and we'll reply within 24 hours, with a first sample in 4 to 10 days.
Get in Touch→