> Title: Hoodie GSM and Construction: A Sourcing Guide | Surajmal
> Source: https://surajmal.com/blog/2026/11/hoodie-sourcing-guide-fabric-gsm-construction
> Publisher: Surajmal Shobhachand

[SSL Newsroom](/blog) Sourcing

# How to Source Hoodies from India: Fabric, GSM and Construction

Kolkata  20 NOVEMBER 2026 By Surajmal Editorial Team10 min read

Published 20 November 2026

A hoodie is specified in seven parts: the body fabric and its weight, the hood, the pocket, the rib, the trims, the wash and the decoration. Most retail hoodies sit between about 280 and 400 GSM in French terry or brushed fleece, and almost every quoting dispute traces back to one of those seven being left open.

Two quotes for "a 320 GSM cotton hoodie" can differ widely and both be fair, because one assumes a two-panel single-layer hood and plain cotton rib, and the other a three-panel lined hood, metal eyelets, cotton-elastane rib and a garment dye. The guide below works through each part in the order a sample room would ask about them.

India's knit clusters, Tirupur above all, have deep capacity in fleece and terry garments; the [Tirupur knitwear guide](/blog/2024/08/tirupur-knitwear-capital) covers how that cluster is organised. Everything that follows applies wherever the order is placed.

## French terry or fleece: which body fabric does a hoodie need?

Both start as the same looped knit. [French terry](/materials/french-terry) leaves the loops on the inner face unbrushed, so it is lighter, cooler and holds a cleaner shape. [Fleece](/materials/fleece) has the loops brushed into a soft nap, which traps warmth and adds bulk at the same weight. Terry suits spring ranges, layering pieces and garment-dyed styles; fleece suits winter weights and the classic heavy pullover.

The fibre is the second decision. Most hoodies are 100% cotton or a cotton-rich blend with polyester, commonly somewhere from 80/20 to 60/40. [Cotton](/materials/cotton) gives a dry hand and takes garment dye and discharge print well. Polyester in the blend reduces shrinkage and speeds drying, at the cost of pilling that stays on the surface and a less natural hand. Organic and recycled versions of both exist and add their own documentation to the programme.

## What GSM should a hoodie be?

Typically 280 to 350 GSM for a midweight hoodie and 350 to 450 GSM for a heavyweight one. Below about 280 GSM a hoodie reads as lightweight or summer weight; above 450 GSM it moves into the heavy, structured streetwear end.

Weight class

Typical fabric GSM

Common body

How it wears

Lightweight

220 to 280

French terry

Drapes, layers under a jacket, suits warmer months

Midweight

280 to 350

French terry or fleece

The core retail weight, year-round

Heavyweight

350 to 450

Fleece or heavy terry

Holds its shape, boxy silhouette, winter

Extra heavyweight

450 and above

Heavy fleece or dense terry

Structured streetwear, high fabric cost

State the GSM on the finished, washed fabric, with a tolerance. A greige fabric gains weight as it shrinks in dyeing and finishing, and a garment-dyed hoodie gains more in the garment wash, so "320 GSM" on the roll and "320 GSM" on the finished garment are different specifications. The [fabric GSM guide](/blog/2026/06/fabric-gsm-weight-guide-apparel-buyers) covers how to write the tolerance.

Weight also changes the pattern. A heavyweight fabric needs more ease at the armhole and a larger hood opening to sit right, and its seams carry more bulk, so a block developed in 280 GSM terry does not transfer cleanly to 420 GSM fleece.

## How should the hood and pocket be constructed?

Specify the hood's panel count, its lining and its opening measurement, and the pocket's type, depth and reinforcement. These are the details that separate a basic hoodie from a premium one, and they are where a sample most often differs from the reference garment.

Element

Common options

What to specify

Hood panels

Two-panel with a centre seam; three-panel with a centre strip

Panel count, and whether the centre strip is self fabric or contrast

Hood lining

Single layer; double layer in self fabric; lined in jersey

Lining fabric and colour, and whether it shows at the opening

Hood opening

Measured edge to edge along the face opening

Measurement with tolerance on every size

Back neck

Neck tape over the seam, or a coverstitched finish

Tape width and fabric

Kangaroo pocket

Patch pouch with turned and topstitched edges

Pocket width, depth, opening angle and height above the hem rib

Split pockets

Two pouches either side of a zip; side-seam pockets

Placement and pocket bag fabric

Reinforcement

Bartacks at pocket ends, stay tape at the zip

Positions and stitch type

A three-panel hood sits closer to the head and holds its shape when down; a two-panel hood is cheaper and peaks at the top. A double-layer hood adds weight and cost and stops the inside face showing, which matters on fleece because the brushed back is a different colour value from the face.

Zip-through hoodies add a zip decision. Moulded plastic and metal zips each need the length set after the body fabric has been shrinkage-tested, because a body that shrinks around a zip that does not leaves a wavy front placket that cannot be pressed out.

## What rib, drawcord and eyelet details need specifying?

The rib's structure and fibre, the cord's shape and tipping, and the eyelet type with its reinforcement. They are small parts with outsized effects on how the garment looks after a month of wear.

Cuff and hem rib is usually 1x1 or 2x2 [rib](/materials/rib), knitted in cotton with a small share of [elastane](/materials/spandex-elastane), commonly around 3 to 5%, so the cuff recovers after being pushed up the arm. Without elastane a cotton rib grows and stays stretched. The rib is often knitted and dyed separately from the body, so its shade has to be approved against the body fabric, not only against the colour standard, or the cuffs read lighter or darker than the sleeve. State rib length at cuff and hem as finished measurements.

Trim

Options

Specification point

Cuff and hem rib

1x1 or 2x2, cotton or cotton-elastane

Structure, elastane share, finished length, shade against body

Drawcord

Flat or round, cotton or polyester

Width, length outside the eyelets, colour

Cord ends

Metal or plastic aglets, silicone tips, knots

Tip type and pull strength

Eyelets

Metal eyelets with a backing washer; embroidered eyelets

Finish, metal composition, reinforcement behind the hole

Cord anchor

Stitched at centre back

So the cord cannot be pulled out

Metal eyelets need a reinforcing layer behind them, usually a small fused patch, or the hole tears under the pull of the cord. Embroidered eyelets avoid metal altogether and suit garment-dyed styles, where metal can mark the fabric in the wash.

Children's hoodies need a separate decision. In the United States, the Consumer Product Safety Commission has determined that hood and neck drawstrings on children's upper outerwear in sizes 2T to 12 present a strangulation hazard and are a substantial product hazard. The [kidswear safety guide](/blog/2026/06/kidswear-safety-compliance-standards) covers how childrenswear programmes handle cords and trims. [\[1\]](https://www.cpsc.gov/Business--Manufacturing/Business-Education/Business-Guidance/Drawstrings-in-Childrens-Upper-Outerwear "Source 1: cpsc.gov: Drawstrings in Childrens Upper Outerwear")

## How do you stop a hoodie shrinking, twisting or pilling?

By controlling the fabric before it is cut. Pre-shrinking, compacting and the right knitting construction prevent most post-wash complaints, and a wash test on a finished sample confirms it before bulk.

Problem

Usual cause

Control

Shrinks in length after washing

Fabric not compacted or pre-shrunk

Compacted finish, shrinkage limit on the tech pack

Side seams twist toward the front

Spirality in tubular knit

Open-width finishing, yarn twist balance, tested spirality limit

Pilling on the face or inside

Brushing loosens fibres; polyester anchors pills

Anti-pill finish, yarn choice, pilling grade

Cuffs and hem stay stretched

Rib without elastane, or weak elastane

Cotton-elastane rib, recovery check

Zip placket waves

Body shrinks more than the zip tape

Shrinkage-tested fabric before zip length is set

Garment-dyed piece comes out small

Garment wash shrinkage not built into the pattern

Pattern graded up for the measured shrinkage

Shrinkage limits are commonly written as a maximum percentage in length and width after a stated wash procedure, and a midweight cotton terry is often specified at around 5% or less.

[Garment dyeing](/techniques/garment-dyeing) changes the arithmetic. The hoodie is sewn in undyed fabric and then dyed and washed as a finished piece, so it shrinks after it is made. The pattern is cut larger by the measured shrinkage, and that figure is only known after a test batch through the actual dye process. Expect some seam puckering and slight colour variation between pieces; the sealed sample sets how much is acceptable.

## Which decoration methods suit a hoodie?

[Screen printing](/techniques/screen-printing) and [embroidery](/techniques/embroidery) cover most hoodie decoration, with [puff printing](/techniques/puff-printing) and [appliqué](/techniques/applique) for raised effects. The choice depends on the artwork, the fabric weight and the wash.

Method

Works best for

Watch on a hoodie

Plastisol screen print

Bold, opaque artwork on any colour

Heavy hand on large prints; cracking if cured wrongly

Water-based and discharge print

Soft hand on cotton, vintage look

Needs high cotton content; colour range on dark grounds

Puff print

Raised graphics and logos

Fine detail fills in; height varies with cure

Flat embroidery

Logos, small chest marks

Puckering on fleece without the right backing

3D puff embroidery

Raised lettering

Needs stable, heavier fabric

Chenille appliqué

Varsity patches, large raised marks

Weight and cost; edges must be secured for washing

Digital or transfer print

Photographic or many-colour artwork

Hand and wash durability vary by system

Embroidery on fleece needs the right stabiliser behind it, because the knit stretches under the needle and puckers once the hoop comes off. The [embroidery and appliqué guide](/blog/2026/10/embroidery-applique-apparel-guide) covers digitising, backing and pricing.

Decide whether decoration goes on cut panels or the finished garment. Printing a flat front panel before sewing is easier to register and cheaper, but it commits the panel before the garment is assembled. Garment-dyed styles are usually decorated after dyeing, since many prints change colour in the dye bath.

## What drives the cost of a hoodie?

Fabric weight, above everything else. A hoodie uses a lot of fabric per piece, and fabric is bought by the kilo, so each step up in GSM raises the cost of every garment. After fabric come finishing, construction details, decoration and packing.

Cost driver

Why it moves the price

Fabric GSM and consumption

More grams per square metre, more kilos per piece

Fibre

Organic cotton and certified recycled fibres cost more and add documentation

Finishing

Brushing, enzyme washing, garment dyeing and washes add process cost and loss

Construction

Three-panel or lined hood, zip, split pockets and extra panels add sewing time

Trims

Rib quality, metal eyelets, custom aglets, branded zip pullers

Decoration

Colours, print size, stitch count, number of placements

Packing and freight

Hoodies are bulky; fewer pieces per carton raise freight per piece

Sampling usually runs in stages: a development or proto sample to settle the fabric and look, a fit sample on the base size, a size set across the range and a pre-production sample in bulk fabric with bulk trims. For a hoodie, add a decoration strike-off and a washed sample that proves shrinkage and twist. The [sampling process guide](/blog/2026/05/garment-sampling-process) explains each round.

Packing deserves a line on the spec. A heavyweight hoodie folded with tissue and a size sticker in an individual polybag takes up far more carton space than a T-shirt, so fold dimensions, polybag size and pieces per carton change landed cost. The [carton and container calculator](/tools/carton-and-container-calculator) works through the cubic volume.

## Short FAQ

**What is a good GSM for a hoodie?**

Typically 280 to 350 GSM for an everyday midweight hoodie. Heavyweight styles run 350 to 450 GSM, and lightweight terry hoodies sit around 220 to 280 GSM.

**Is 400 GSM a heavy hoodie?**

Yes. At 400 GSM a hoodie sits firmly in the heavyweight band, with a structured hang and noticeably more warmth than a midweight piece.

**Does a cotton-polyester blend shrink less than 100% cotton?**

Yes, generally. The polyester share reduces shrinkage and speeds drying, though it raises the risk of visible pilling over time.

**Should cuffs and hem rib contain elastane?**

Yes, in most programmes. A small elastane share lets the rib recover after stretching, where a pure cotton rib tends to stay stretched out.

**Can a hoodie be garment dyed after decoration?**

Sometimes, but not with every method. Many prints change colour or texture in the dye bath, so decoration is usually applied after dyeing unless a dye-safe method has been tested.

## Write the seven parts down before the first quote

A hoodie quote is only comparable once the body fabric and finished GSM, the hood, the pocket, the rib, the trims, the wash and the decoration are fixed on paper. Settle those, test shrinkage and twist on a washed sample, and approve rib shade against the body, and most of the problems that surface in bulk never arrive. Surajmal Shobhachand supplies [hoodies and sweatshirts](/products/hoodies-sweatshirts) in loopback terry and brushed fleece.

Related pages

-   [Hoodies & sweatshirts](/products/hoodies-sweatshirts)
-   [Knitwear](/products/knitwear)

Share[](https://www.linkedin.com/sharing/share-offsite/?url=https%3A%2F%2Fsurajmal.com%2Fblog%2F2026%2F11%2Fhoodie-sourcing-guide-fabric-gsm-construction) [](https://twitter.com/intent/tweet?url=https%3A%2F%2Fsurajmal.com%2Fblog%2F2026%2F11%2Fhoodie-sourcing-guide-fabric-gsm-construction&text=How%20to%20Source%20Hoodies%20from%20India%3A%20Fabric%2C%20GSM%20and%20Construction) [](https://wa.me/?text=How%20to%20Source%20Hoodies%20from%20India%3A%20Fabric%2C%20GSM%20and%20Construction%20https%3A%2F%2Fsurajmal.com%2Fblog%2F2026%2F11%2Fhoodie-sourcing-guide-fabric-gsm-construction) [](mailto:?subject=How%20to%20Source%20Hoodies%20from%20India%3A%20Fabric%2C%20GSM%20and%20Construction&body=https%3A%2F%2Fsurajmal.com%2Fblog%2F2026%2F11%2Fhoodie-sourcing-guide-fabric-gsm-construction)

Surajmal Editorial Team

The Surajmal Editorial Team writes from inside a working textile export house in Kolkata, drawing on experience manufacturing garments, fabrics, and yarns for global retail buyers since 1968. Every article is reviewed by practitioners who source, sample, and ship the products they write about.

On this page

-   [French terry or fleece: which body fabric does a hoodie need?](#french-terry-or-fleece-which-body-fabric-does-a-hoodie-need)
-   [What GSM should a hoodie be?](#what-gsm-should-a-hoodie-be)
-   [How should the hood and pocket be constructed?](#how-should-the-hood-and-pocket-be-constructed)
-   [What rib, drawcord and eyelet details need specifying?](#what-rib-drawcord-and-eyelet-details-need-specifying)
-   [How do you stop a hoodie shrinking, twisting or pilling?](#how-do-you-stop-a-hoodie-shrinking-twisting-or-pilling)
-   [Which decoration methods suit a hoodie?](#which-decoration-methods-suit-a-hoodie)
-   [What drives the cost of a hoodie?](#what-drives-the-cost-of-a-hoodie)
-   [Short FAQ](#short-faq)
-   [Write the seven parts down before the first quote](#write-the-seven-parts-down-before-the-first-quote)

More from the newsroom

-   [Sourcing · 11 min What Is Elastane? Stretch Percentages, Fabrics and Care in Garments](/blog/2026/11/what-is-elastane-spandex-in-garments)
-   [Sourcing · 11 min Combed vs Carded vs Ring-Spun Cotton: What Each Means on a Garment Spec](/blog/2026/11/combed-vs-carded-vs-ring-spun-cotton)
-   [Sourcing · 11 min How to Find a Clothing Manufacturer in India: Where to Look and How to Shortlist](/blog/2026/11/how-to-find-a-clothing-manufacturer-in-india)

START A CONVERSATION

## Ready to source with _confidence?_

Send a brief and we'll reply within 24 hours, with a first sample in 4 to 10 days.

[Get in Touch→](/contact)
